DENO LED Lighting

Recessed LED Channel | Plaster-In Aluminum Profile | DENO

Trimless and flanged recessed LED channels from 8.89x7.79mm to 22x12mm. Plaster-in drywall profiles for 4-10mm strips, frosted covers, end caps and clips.

Recessed LED Channel models & key specifications (6)

DL-0809HX-F — 120 LEDs/m

DL-0809HX-F Recessed LED Channel — 4/5mm FPCB width, 120 LEDs/m

LED Density: 120leds/m or above · PCB Width: 4/5mm

DL-1510 HX-F — 2835 · 120 LEDs/m · 24V

DL-1510 HX-F Recessed LED Channel — 24V, cuttable every 62.5mm, 10mm FPCB width, 2835 LEDs, 120 LEDs/m

LED Type: 2835 · LED Density: 120leds/m or above · Voltage: DC 24V · Cutting Unit: 8LEDs/62.5mm · PCB Width: 10mm · Copper Foil: 3oz · Circuit Type: CV

DL-1010HX-F — 2835 · 120 LEDs/m · 24V

DL-1010HX-F Recessed LED Channel — 24V, cuttable every 35.7mm, 6mm FPCB width, 2835 LEDs, 120 LEDs/m

LED Type: 2835 · LED Density: 120leds/m or above · Voltage: DC 24V · Cutting Unit: 6LEDs/35.71mm · PCB Width: 6mm · Copper Foil: 3oz · Circuit Type: CV

DL-1409B HX-F — 120 LEDs/m

DL-1409B HX-F Recessed LED Channel — 8mm FPCB width, 120 LEDs/m

LED Density: 120leds/m or above · PCB Width: 8mm

DL-1707HX-F — 2835 · 120 LEDs/m · 24V

DL-1707HX-F Recessed LED Channel — 24V, cuttable every 50mm, 10mm FPCB width, 2835 LEDs, 120 LEDs/m

LED Type: 2835 · LED Density: 120leds/m or above · Voltage: DC 24V · Cutting Unit: 12LEDs/50mm · PCB Width: 10mm · Copper Foil: 3oz · Circuit Type: CV

DL-2212B HX-F — 2835 · 120 LEDs/m · 24V

DL-2212B HX-F Recessed LED Channel — 24V, cuttable every 62.5mm, 10mm FPCB width, 2835 LEDs, 120 LEDs/m

LED Type: 2835 · LED Density: 120leds/m or above · Voltage: DC 24V · Cutting Unit: 8LEDs/62.5mm · PCB Width: 10mm · Copper Foil: 3oz · Circuit Type: CV

Recessed & Plaster-In LED Channel — Buyer Questions

What is a recessed LED channel?

A recessed LED channel sits inside the ceiling or wall so only the diffuser is visible. Flanged bodies such as the 22x12mm and 14.2x9.8mm profiles rest on the plasterboard face and are the fastest to install; plaster-in versions are skimmed over for a trimless finish with no visible frame at all. Both need a routed slot slightly wider than the body so the flange can sit flat.

How much ceiling depth does a plaster-in LED profile need?

Take the profile height plus roughly 5mm of clearance for wiring. The shallow 17x7mm body only needs about 12mm behind the board, the 15.2x10.4mm slim profile about 15mm, and the deep 22x12mm body about 17mm — which is why the slim bodies are specified for suspended ceilings with limited plenum, and the deep bodies where heat dissipation matters more than depth.

Which recessed profile suits a 5mm micro LED strip?

The 8.89x7.79mm mini recessed body takes 4/5mm FPCB and is the smallest trimless housing in the range. It is the one to use for narrow shadow gaps, joinery reveals and slim wall-wash lines where a standard 10mm slot would look heavy, and it still gives the frosted cover enough gap to smooth a 120 LEDs/m tape.

Can a drywall LED channel be installed after the ceiling is finished?

A flanged body can: cut the slot, drop the profile in and the flange covers the cut edge. A true plaster-in extrusion has to go in before skimming, because the mesh wing is bedded into the compound. Plan feed points at the same time — a recessed run is far harder to re-open than a surface line, so bring the driver cable to one end or the mid-point before closing the ceiling.

What accessories come with a trimless LED profile?

Each bar ships with end caps (solid and cable-entry), a frosted PC cover as standard, and mounting clips or spring brackets depending on the body. Opal and clear covers, corner joints and continuous-run couplers are available on request, and DENO supplies the matched LED strip cut to the same length so the assembly arrives ready to install.