DENO LED Lighting

RGBW LED Sheet | Backlit Stone Lightbox Colour + White 24V

RGBW and 5-in-1 LED sheets for backlit marble and onyx lightboxes: true white plus colour, 24V, precise grid cutting, dot-free at 20-40mm cavity depth.

RGBW LED Sheet models & key specifications (4)

6432 — 5050 · 288 LEDs/m · 24V

6432 RGBW LED Sheet — 24V, cuttable every 20*240mm, 240x480mm FPCB width, 5050 LEDs, 288 LEDs/m, IP20

LED Type: 5050 · LED Density: 288 LEDs/pcs · Voltage: DC 24V · Power: 20~110W(1pcs) · Cutting Unit: 12LEDs/20*240mm · PCB Width: 240x480mm · Copper Foil: 2oz · Circuit Type: CV · IP Rating: IP20

16795 — 5050 · 98 LEDs/m · 24V

16795 RGBW LED Sheet — 24V, cuttable every 34.286*240mm, 240x480mm FPCB width, 5050 LEDs, 98 LEDs/m, IP20

LED Type: 5050 · LED Density: 98 LEDs/pcs · Voltage: DC 24V · Power: 12~26.8W · Cutting Unit: 7LEDs/34.286*240mm · PCB Width: 240x480mm · Copper Foil: 2oz · Circuit Type: CV · IP Rating: IP20

16797 — 5050 · 288 LEDs/m · 24V

16797 RGBW LED Sheet — 24V, cuttable every 120mm, 480*240mm FPCB width, 5050 LEDs, 288 LEDs/m

LED Type: 5050 · LED Density: 288LEDs/pcs · Voltage: DC24V · Cutting Unit: 12LEDs/120mm · PCB Width: 480*240mm · Copper Foil: 2oz · Circuit Type: CV

16796 — 5050 · 162 LEDs/m · 24V

16796 RGBW LED Sheet — 24V, cuttable every 53.333*80mm, 240x480mm FPCB width, 5050 LEDs, 162 LEDs/m, IP20

LED Type: 5050 · LED Density: 162 LEDs/pcs · Voltage: DC 24V · Power: 13~50W · Cutting Unit: 6LEDs/53.333*80mm · PCB Width: 240x480mm · Copper Foil: 2oz · Circuit Type: CV · IP Rating: IP20

RGBW LED Sheet — Buyer Questions

What is the difference between an RGBW and an RGBWW LED sheet?

RGBW adds one white die to the RGB mix; RGBWW (the 5-in-1 #6432) adds warm and cool white, so the white channel itself tunes from about 2700 K to 6500 K. The 5-in-1 also puts all five dies in a single chip, which removes the colour fringing you see from separate dies at short diffuser distances.

Which RGBW LED sheet density should I specify?

98 LEDs (#16795) for low-load, large-area work with 30–40 mm of diffuser depth; 162 LEDs (#16796) when you need two-axis cutting to shape the sheet around fixtures; 288 LEDs (#16797) on a 19.91 mm pitch when the cabinet is shallow and the surface is viewed close up.

Why choose RGBW over RGB for backlit signage?

Because most signs display white most of the time. An RGB mix always carries a colour cast and burns all three channels to make it; the dedicated white die gives a clean, colour-correct white at lower power, while the colour channels stay free for seasonal or promotional scenes.

Can an RGBW LED sheet be cut in two directions?

The #16796 can: its 53.3 × 80 mm grid allows cuts across and along the sheet, so it can be shaped around bar backs, curved fixtures and display niches instead of being masked off. The other RGBW sheets cut on a single axis at 34.3 mm or 120 mm intervals.