DENO LED Lighting

360° LED Neon Flex — Round Neon Rope | DENO

DENO LED's 360 degree LED neon flex offers uniform, omnidirectional illumination for diverse architectural and decorative lighting applications. Available in 24VDC, these products feature high CRI (Ra>90) for accurate color rendering and various wattages (e.g., 10-15W/m) to suit specific brightness requirements. With IP67 protection, they are suitable for both indoor and outdoor installations, providing continuous light lines with precise cut units for custom lengths. Typical applications include accent lighting, signage, and creative installations requiring full-round light emission.

360° Series models & key specifications (4)

DL-FCN25 — 128 LEDs/m · 24V

DL-FCN25 360° Series — 24V, cuttable every 62.5mm, 10(2PCS) FPCB width, ≥ 128 LEDs/m LEDs/m, IP65

LED Density: ≥ 128 LEDs/m · Voltage: DC24V · Cutting Unit: 8LEDs/62.5mm · PCB Width: 10(2PCS) · IP Rating: IP65

DL-T22D3 — 120 LEDs/m · 24V

DL-T22D3 360° Series — 24V, cuttable every 125mm, 10(2PCS) FPCB width, ≥ 120 LEDs/m LEDs/m, IP67/IP68

LED Density: ≥ 120 LEDs/m · Voltage: 24V DC · Cutting Unit: 15LEDs/125mm · PCB Width: 10(2PCS) · IP Rating: IP67/IP68

DL-NFT22D1 — 120 LEDs/m · 24V

DL-NFT22D1 360° Series — 24V, cuttable every 14.3mm, 8(2PCS) FPCB width, ≥ 120 LEDs/m LEDs/m, IP67

LED Density: ≥ 120 LEDs/m · CRI: Ra≥80 · Voltage: 24V DC · Cutting Unit: 7LEDs/14.28mm · PCB Width: 8(2PCS) · IP Rating: IP67

DL-T22D2 — 120 LEDs/m · 24V

DL-T22D2 360° Series — 24V, cuttable every 14.3mm, 8(2PCS) FPCB width, ≥ 120 LEDs/m LEDs/m, IP67

LED Density: ≥ 120 LEDs/m · Voltage: DC 24V · Cutting Unit: 7LEDs/14.28mm · PCB Width: 8(2PCS) · IP Rating: IP67

Other Neon LED Strip series

How 360° round LED neon flex performs on site

Specification notes for this section low-voltage DC silicone neon: what it does outdoors, what it does around water, and how far it bends when you trace a building.

Outdoor & façade exposure

Specify for permanent exterior installation above the waterline (IP67).

The silicone is injection moulded onto the FPCB in one shot, so there is no glued cover to open up after a winter of thermal cycling — the failure mode PVC neon rope light shows in its second outdoor summer. UV-stabilised silicone keeps its colour instead of yellowing, and the body stays elastic from −30 °C to +80 °C, so a façade run installed in summer will not go brittle in a January frost. Feed with low-voltage DC and plan short runs per feed to hold end-of-run brightness across a long elevation.

  • Sealed silicone body
  • UV-stable silicone, −30 °C to +80 °C
  • Low thermal load

Pools, spas & wet areas

Suitable for pool surrounds, spa ceilings and steam-adjacent joinery — not for submersion.

IP67 covers rain, splash, wash-down and steam — pool decks, shower reveals, sauna ceilings and spa coves — but the body is not intended to sit under water. Mount it above the waterline in an aluminium groove so condensate drains away from the feed joint, run low-voltage DC for wet-zone safety, and choose the IP68 variant where the channel can flood.

  • IP67 — splash and rain, not submersion
  • low-voltage DC
  • Moulded end cap and feed joint

Architectural contour & signage

Bends in every direction — the body is a round tube at free-form radii — the right pick for handrails, tree wraps, columns and free-form sculptural runs.

360° round LED neon flex takes its curve in every direction — the body is a round tube, which is what decides whether a shape is possible without cutting and re-soldering. At free-form radii the outside of the curve stays evenly lit: the LED pitch is matched to the diffuser depth so you read a continuous line of light rather than dots, even at 30 cm. Printed cut marks with indexed solder pads underneath let a sign maker shorten a letter stroke on site and re-seal it, and mounting clips, aluminium grooves and moulded bend grooves cover surface, recessed and free-form fixing.

  • Compact silicone body
  • Bend radius free-form radii
  • Dot-free diffusion

360 Degree LED Neon Flex — Buyer Questions

What is a 360 degree LED neon flex?

A 360 degree LED neon flex is a round silicone body — typically 20 mm to 25 mm in diameter — with LEDs mounted so light leaves the whole circumference instead of one face. It replaces the old round neon rope light in exposed applications: suspended rings, handrails, tree wraps and free-standing sculptural lines where the viewer sees the tube from every side.

How is a round LED neon tube light different from a rope light?

A traditional rope light uses spaced LEDs inside a clear PVC tube, so you see dots and the PVC yellows outdoors. A round LED neon tube light uses a dense FPCB inside a moulded diffusing silicone body: continuous light, no visible dots, no yellowing, and a proper IP67 seal instead of a crimped cap.

What beam angle does an omnidirectional LED neon give?

The circular section produces a true 360° distribution with no dark seam along the back, unlike a top bend body that emits over roughly 120–160°. For a suspended ring or a wrapped column, the omnidirectional LED neon keeps brightness constant as the observer walks around it — the reason it is specified for retail atria and event structures.

Can a 360 neon flex be bent in any direction?

Yes — a round body has no preferred bend axis, so it takes horizontal and vertical curves alike, typically down to R60–R80 mm depending on diameter. That freedom is why circular neon flex is chosen for free-form artwork and signage scripts that mix directions inside one continuous run.

How is a 360° neon flex mounted?

Three common methods: suspension by stainless wire through moulded eyelets, saddle clips at 300–500 mm centres, and a semi-circular aluminium groove where only part of the tube shows. Because the body emits all round, mounting hardware is kept slim so it does not cast a shadow line along the run.

Is 360 neon available in RGB or tunable white?

Yes. The round platform accepts single colour 2700–6500K, tunable white, RGB and RGBW light engines, plus addressable builds for chase and gradient effects. Control is standard constant-voltage PWM, DALI DT8 or DMX512 through a decoder, so it drops into an existing architectural control system.

Frequently asked questions

What are the primary applications for 360 degree LED neon flex?

360 degree LED neon flex is primarily utilized for applications requiring omnidirectional, uniform illumination. This includes architectural accent lighting, decorative installations, custom signage, artistic lighting features, and any scenario where a continuous, fully-rounded light source is desired for visual impact or functional illumination.

What are the available voltage and power consumption options for DENO LED's 360 degree neon flex?

Our 360 degree LED neon flex products are typically available in 24VDC to ensure stable performance and minimize voltage drop over longer runs. Power consumption varies by model, generally ranging from 10 to 15 Watts per meter, depending on the specific lumen output and LED configuration required for the application.

Can the 360 degree LED neon flex be cut to custom lengths, and what is the minimum cut unit?

Yes, DENO LED's 360 degree LED neon flex is designed for custom length installations. Each model has a specified minimum cut unit, typically ranging from 50mm to 100mm, allowing for precise adjustments to fit project dimensions. Cutting should only be performed at designated marks to maintain functionality and IP rating.

What level of ingress protection (IP rating) does the 360 degree LED neon flex offer, and is it suitable for outdoor use?

Our 360 degree LED neon flex products typically carry an IP67 rating, indicating robust protection against dust ingress and the effects of temporary immersion in water. This makes them suitable for a wide range of outdoor applications, including facades, landscaping, and other environments exposed to weather conditions.